Menu
Menu
Your Cart
Privacy Policy
We use cookies and other similar technologies to improve your browsing experience and the functionality of our site. Privacy Policy.

NX3 3D Flight Controller Gyroscope Balance For Fixed-wing Aircraft

NX3 3D Flight Controller Gyroscope Balance For Fixed-wing Aircraft
NX3 3D Flight Controller Gyroscope Balance For Fixed-wing Aircraft
NX3 3D Flight Controller Gyroscope Balance For Fixed-wing Aircraft
NX3 3D Flight Controller Gyroscope Balance For Fixed-wing Aircraft
NX3 3D Flight Controller Gyroscope Balance For Fixed-wing Aircraft
NX3 3D Flight Controller Gyroscope Balance For Fixed-wing Aircraft
NX3 3D Flight Controller Gyroscope Balance For Fixed-wing Aircraft
459 SEK
  • Stock: In Stock
  • SKU: SKU104734
NX3 3D Flight Controller Gyroscope Balance For Fixed-wing Aircraft







Description:
Voltage Range: 5-6V DC.
Dimensions: 40mm x 25mm.
Weight: 6.5g.

Feature:
1.Four Model Types supported: single aileron, dual ailerons , flapperons, delta and vtail.
2.Three Flight Modes supported:
a. Rate Mode ,Rate Mode for offset correction.
b. Hold Mode ,HOLD mode for attitude hold
c. Gyro Off Mode,transsmiter control the plane directly.
3.Two kinds of Gain Control Method supported:Master Gain from the radio, Independent Axis Gain from the Variable resistor on the Controller board.
4.Using superior algorithm, Bring a more comfortable and more sensitive sense of control .

VERY IMPORTANT :
The Controller has to re-learn center position after installation,or replacing a new radio system, or making a trimming(or Sub-Trim)change within the transmitter, otherwise the servos may move to one side automatically when switching to hold mode.To do this,just quickly flip the flight mode switch twice between rate mode and hold mode within 1 second!

Status LED Description:
LED OFF: NX3 in Gyro Off Mode.
LED ON: NX3 in Rate Mode.
LED flash: NX3 in Hold Mode.

WARNING :
PLEASE READ THE FOLLOWING STEPS VERY CAREFULLY BEFORE YOU START TO INSTALL A NEW PLANE!

Step 1:Mounting
The board need to be firmly mounted near the center of the gravity of the plane by using the double-tape provide.Please make sure the longer side of the board is along with the heading direction.After mounting ,please check again if the board is attached firmly in the plane.
Step 2:Model Type Selection
The DIP switches set the WING mode,Please match the type of your aircraft with Normal Airplane(single aileorn),Normal Airplane(dual aileron for flapperon), Delta-wing (Flywing-wing)and V-tail according the pictures 1 to 4. if you change any DIP switch settings, power cycle the device to enable the new setting to take effect.
Step 3:Wiring
Please connect the control board and the radio receiver using wires provide according the pictures 1 to 4.Pay attention to the color  of  wires to avoid anti-plug.




Step 4:Switch and Master Gain Channel Configure
Assign a 3-pos switch to the channel which connected the pins”IN-4”(AUX-IN) for switching the flight mode in flight.When use a 2-pos swtich,you can only switch between Rate Mode and Hold Mode,So you can not switch to Gyro Off Mode.It will be set to Rate Mode by default if switch channel is not connected to the board.  If your transsmiter has Travl Adjust Function(End Point Adjust Function),you can change the switch channel’s End Point to change Master Gain.
Step 5:Gyro direction and Gyro Gain configure
Befor flight, you have to verfy that the gyro compensation direction is OK, otherwise, it could lead to losing control or even crash during the flight!the VR gain POTs on the NX3 control the correction gain and direction for each of the pitch (ELE), roll (AIL) and yaw (RUD) axis.
5 o'clock = max gain in one direction
12 o'clock = zero gain
7 o'clock = max gain in opposite direction

To perform the examination,power on the
board,pick the plane up and check it by
following the six steps below:

Step 6: re-learn center position
Quickly flip the flight mode switch twice between rate mode and hold mode within 1 second!
Thanks for using NX3 Flight Controller. if u have any questions, plz feel free to contact clarencetuan.mat@gmail.com

Packing Included:
1 x NX3 Flight Controller board
1 x NX3 manual  
5 x wires
1 x double-side tape.

When you order from Bazaargadgets.com, you will receive a confirmation email. Once your order is shipped, you will be emailed the tracking information for your order's shipment. You can choose your preferred shipping method on the Order Information page during the checkout process. Bazaargadgets.com offers four different international shipping methods:

 

Shipping from Chinese Warehouse
Airmail and register airmailAreatime
United States,Canada10-20 business days
Australia,New Zealand,Singapore14-28 business days
United Kingdom, France, Spain, Germany, Netherlands, Japan, Belgium, Denmark, Finland, Ireland, Norway, Portugal, Sweden, Switzerland14-28 business days
Brazil15-35 business days
Russia15-35 business days
Other countries14-28 business days
Priority Direct MailAustria, Belgium,Denmark,Finland,France,Germany,Greece,Italy,Netherland,Portugal,Spain,Sweden7-10 business days
United States6-9 business days
United Kingdom5-10 business days
EMS10-15 business days to worldwide
Expedited Shipping5-8 business days to worldwide

 

NOTE: Netherlands Direct Mail has been combined into the Priority Direct Mail. If you are in a European country; simply choose Priority Direct Mail and it will be shipped via Netherlands Direct Mail.

 

*Expedited shipping can not be used for PO Box addresses

 

In addition, the transit time depends on where you're located. If you want to know more information, please contact the customer service. We will settle your problem as soon as possible. Enjoy shopping!

 

Write a review

Note: HTML is not translated!
Rating
Bad Good
Captcha